We collect basic data about your visit to our website. We will place a cookie onto your computer to remember your choice. See our Privacy and Cookie Policy


Our extensive industry experience means that we hold a lot of valuable knowledge and we would like to share this knowledge with you.

Here you will find blog posts from the SIDERISE team including articles written by our technical experts. Find out more about our products and what’s going on in the industry for acoustic, fire and thermal insulation.

Noise is all around us, in our place of work, commuting, and even in the sanctity of our homes. It’s hard to escape the incessant digital bleeps of technology, noise from co-workers, outside traffic and the drone of building services.

Good or bad, the acoustical environment in buildings is ultimately a result of design and so it’s never been more important for architects and building engineers to silence a well-known source of undesirable noise and vibration – heating, ventilation and air condition systems. 

A fundamental element of buildings across a wide range of sectors, building services equipment can create unwanted noise problems leading to workplaces that are uncomfortable and less productive. Noise sources can include everything from fans to variable air volume systems; grilles and diffusers to roof-top units; fan coil units to chillers, compressors and condensers; pumps and stand-by generators; boilers and cooling towers.

As we create more energy efficient and airtight buildings, this has a knock-on impact both thermally and acoustically. However, this further drives the need for ventilation and thermal management, and this required airflow can then introduce a noise issue of its own, both break-out and in-line noise.

Break-out noise is where sound transmits through the wall of ducting and into the room through which the ductwork is travelling.  In-line (duct-borne) noise or noise traveling through ductwork can create unwelcome high levels of background noise if not properly managed. This noise can raise stress levels in the workplace, harming communication and concentration and increasing fatigue. A poorly designed acoustic solution can potentially exacerbate issues by causing regenerative noise, and negatively affecting airflow. There’s also the issue of cross-talk, whereby speech privacy is compromised by room-to-room transmission via the ventilation system.

Air velocity within a duct system is another important element as it influences the noise levels significantly. Regenerated noise can be created by transition pieces, bends, dampers, grilles and diffusers. Regenerated noise can be reduced by limiting the air velocities within the duct system; by easing transitions in the system design and by ensuring that internal acoustic treatments contain chamfers where appropriate to reduce the turbulent effect of sudden changes in opening or direction.

When two adjacent or closely positioned rooms are sharing the same ductwork, sound travels within ducts and will decrease the room-to-room sound insulation dramatically. This, will of, course impact speech privacy and negatively affect the working environment through disturbance.

Vibration and sound energy from HVAC operation will transmit to a structure and be redistributed around a building.  By isolating your systems from the structure before it has a chance to vibrate, through isolation mounts or decoupled through flexible linkages from the structure via the noise source and the duct runs, another path of noise has been reduced through physical materials.

Silent treatment

The SIDERISE range of noise control solutions can be tailored to meet project -specific design and performance requirements such as the octave band requirements of your HVAC unit, thereby delivering the optimum acoustic performance at the minimum cost. Manufactured from high performance open cell acoustic foam, parts are designed to ease airflow and lower regenerative noise, and the lining treatment is engineered to deliver the lowest possible Sound Power (LwA). These acoustic solutions give exceptional noise absorption, yielding reduced airborne noise at inlets and outlets, and lowering case radiated noise.  Lining kits are Class 0 fire rated to EN 13501-1 to comply with Building Regulations Approved Document B.

Supplied as an easy-to-fit, pre-cut kit and backed with high performance modified acrylic adhesive for rapid installation on a manufacturer’s assembly-line, these noise control solutions offer exceptional performance for fan coil units, air handling units and heat exchangers.

Existing buildings can benefit too. If there is a ductwork ‘in-line’ noise problem, open-cell melamine resin foams are an easy and cost-efficient way to introduce noise control.  At the terminal ends, where air is being delivered to the occupied spaces, you can remove the grille and simply install the foam inserts. Inherently flexible, the inserts are ideally suited to retro-fit installation, particularly in situations where there is minimal access and/or where less disruption is a consideration.  For ‘duct noise breakout’ another solution, which contributes well to quiet air-handling, are externally applied acoustic treatments. Easy to install without disturbing the HVAC system, this solution reduces break-out noise by providing a combination of acoustic absorption and sound reduction via inherently damped flexible mass membrane.

While it’s difficult to escape sound completely, by proactively considering potential acoustic problems at the design stage of a HVAC system and adding sound control measures to minimise unwanted noise, building owners will have a far quieter system, which in the end, can go a long way towards promoting comfort and productivity.  

A value is required.

A value is required.Invalid format.

A value is required.

A value is required.

Any information we receive will be treated in commercial confidence in line with our Privacy Policy

Your e-mail address will not be made public, shared with any third party or used for marketing purposes. We will only use your e-mail address should we need to contact you with regards to your comment.

Noise accounts for most of the complaints that local councils and the Environment Agency receive about environmental pollution and is a major cause of stress.

Given that construction sites generate significant levels of noise, which is always varied and changing, what noise control methods do contractors have at their disposal to minimise the impact of noise from such works on nearby residents and businesses?

Noise during construction is balancing act between the needs of the developer and the rights of local residents.  It is one of the most difficult things to control, which is down in many ways to the size of the site, the changes in location of machinery and the transient nature of the construction. From drills to sledgehammers, electric saws to cement mixers, earth moving equipment to generators; the noise generated by these activities can be an unhealthy mix of high intensity and continuous.  It can lead to high blood pressure, extreme stress and in worst cases damage to hearing.

While there are number of ways to control environmental noise on construction sites, through the use of quieter equipment, limiting construction hours, or creating noise perimeter zones, one of the most effective ways of reducing construction site noise is through the use of purpose-built perimeter noise control barriers.

Noise control barriers are a fast and cost effective way of dealing with construction site noise, reducing complaints as well as promoting good relations between the construction industry and the local community.

These noise control barriers are made from a composite of durable acoustic facing material, acoustically absorbent core and flexible mass membrane, delivering both optimum sound absorption and sound insulation. By designing the noise barriers to absorb noise on the side facing the noise source, unwanted sound reflections are reduced, and this in combination with the designed sound reduction through mass, lowers both the ambient and transmitted sound to the environment and nearby residences.

Quickly fixed to site fencing and scaffolding, they can absorb both noise on site for operators and create a beneficial environmental noise reduction to the outside community. Due to their unique design they offer outstanding performance whilst still being easily rolled, handled and stored.

Construction noise is part of any development.  Simple straightforward solutions such as noise control barriers can be the difference between a site being up and running and an unwelcome visit from the local environmental health officer.  And they do not require extensive acoustic experience on the part of the contractor.

A value is required.

A value is required.Invalid format.

A value is required.

A value is required.

Any information we receive will be treated in commercial confidence in line with our Privacy Policy

Your e-mail address will not be made public, shared with any third party or used for marketing purposes. We will only use your e-mail address should we need to contact you with regards to your comment.


Technical resources

Make an enquiry

Whatever your insulation requirement, whether you are in the construction, marine, transport or energy generation sector, we can provide technical advice and a tailored insulation solution.

Talk to our technical advisory team who will be happy to have a look at your project.

Talk to us